Residential · Charlotte, NC
When an old coating is peeling, bubbling, or slick, epoxy removal is the only way to get a recoat to bond and last. Elite Epoxy Charlotte has served Charlotte since 2017, removing failed epoxy and installing new, high-build floor systems for garages, shops, and commercial interiors.
Removal starts with the substrate, not the topcoat. We confirm what you have (epoxy, polyaspartic, urethane, paint, or acrylic sealer), then choose the right process, typically diamond grinding with HEPA dust control, shot blasting for heavier profiles, or a combination for thick build-ups and hot-tire pickup. After removal, we check concrete soundness, moisture vapor transmission risk, and contamination from oil, tire plasticizers, silicones, and curing compounds. Cracks, spalls, and control joints are repaired with epoxy paste, polyurea joint filler, or rapid-set cementitious patch, then re-profiled so the new system sits flat and continuous.
Local conditions matter for cure and long-term wear. In Charlotte humidity swings and seasonal temperature changes can push moisture through slabs, so we use moisture-tolerant primers and, when needed, a moisture-mitigation epoxy vapor barrier before the build coats. Finish is selected around traction, chemical exposure, and cleaning routines, from broadcast vinyl flake floors with a polyaspartic topcoat to quartz broadcast systems for wet areas, to solid-color epoxy with an aliphatic urethane for abrasion resistance and UV stability at doors. Slip resistance is tuned with aluminum oxide or polymer grit so the floor is safer without turning it into a dirt trap.
Charlotte customers choose us because we treat epoxy removal like a controlled renovation, not a quick scuff-and-coat. You get clear scope, test spots when needed, and a written plan that specifies surface profile, primer type, broadcast rate, and topcoat chemistry so expectations are set before we start. Our crews use commercial grinders, shot blasters, edge tools, and HEPA vacuums to reach perimeter walls, stem walls, and tight corners where failures often begin. We are licensed and insured, and we keep downtime predictable by staging the work, protecting adjacent finishes, and coordinating cure windows around your access needs.
We finish with a documented walkthrough and care plan so the new coating performs. Before we leave, we verify coverage at edges and transitions, confirm texture consistency, and review cure times for foot traffic, vehicles, lifts, and chemical exposure. You receive a free written estimate, product data on the installed system, and maintenance guidance such as neutral-pH cleaning, de-icing chemical limits, and how to prevent tire staining and scratching from metal stands. If your slab needs ongoing joint maintenance, we explain when to re-fill or re-topcoat so you can budget instead of reacting to failure.
Many garage floors are completed in 1-2 days depending on prep, crack repair, and the coating system. Commercial projects vary by square footage, cure time, and access, we’ll outline the schedule in your written estimate.
Light foot traffic is often possible within 12-24 hours for fast-cure systems, while vehicle traffic commonly requires 24-72 hours. Actual return-to-service depends on temperature, humidity, and the specific product data sheet.
Sometimes, but only after proper removal or profiling. We typically grind to remove loose material and create a sound surface, then rebuild the system so the new coating bonds to stable concrete.
Yes, when the slab condition indicates elevated moisture risk. We can specify moisture-tolerant primers or barrier coats and detail the system based on the site evaluation.
Common options include full broadcast vinyl flake, metallic epoxy, solid color epoxy, and clear coats in gloss, satin, or matte. We also offer traction additives and chemical-resistant topcoats depending on use.
Epoxy removal is the step most installers try to skip, and it is the reason many recoats peel within months. If your garage or commercial floor has delamination, fisheyes, hot-tire pickup, or worn-through topcoat, removing the failed coating down to clean, profiled concrete is the safest path to a durable new system. Elite Epoxy Charlotte handles full removal, surface preparation, and recoating with epoxy, polyaspartic, and urethane systems built around your traffic and cleaning needs.
Most coating failures trace back to poor adhesion. Our epoxy removal process focuses on mechanically preparing the slab to the right surface profile, then rebuilding the system in layers, primer, body coat, broadcast (optional), and topcoat. For garages and light industrial floors, that often means a 100 percent solids epoxy base with a full flake broadcast and a polyaspartic clear coat for fast return to service. For commercial interiors or chemical exposure, we may specify an epoxy build coat and an aliphatic urethane topcoat for abrasion and stain resistance.
We also address what is under the coating, oil contamination, soft or dusty concrete, and moisture vapor that can push coatings off the slab. When testing or job conditions indicate risk, we install a moisture-mitigation epoxy primer and detail joints and cracks with the right repair materials so the finish stays uniform. You get a floor that looks consistent at edges, drains, and thresholds, and performs under vehicles, carts, and daily cleaning.
If you are comparing quotes, ask how the contractor will remove the existing coating and what profile they will leave behind. Proper epoxy removal takes the right equipment, time, and a system spec that matches your use case. Contact Elite Epoxy Charlotte for a free written estimate and a clear recoating plan.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Charlotte. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
